Search found 24 matches

Return to advanced search

Re: DiSEqC on Slave Tuners for Unicable setups

Hi sir the 6508 can not send the diseqc CMD from the slave-demod. Because it 's diseqc pin has not connect to external devices. Best Regards yes, crazycat made this already clear, but there should be no blocking reason (we just have to make sure two diseqc messages aren't sent at the same time) for...
by LSD
Mon Nov 07, 2022 3:11 pm
 
Forum: TBS6508 Multi-standard Octa Tuner PCI-e Card
Topic: DiSEqC on Slave Tuners for Unicable setups
Replies: 6
Views: 528

Re: DiSEqC on Slave Tuners for Unicable setups

The big question now is if we need to fix this for every dvb software which is out there or if the driver can be modified to use the first demod even if it was intended for the second one?
by LSD
Sat Nov 05, 2022 5:05 pm
 
Forum: TBS6508 Multi-standard Octa Tuner PCI-e Card
Topic: DiSEqC on Slave Tuners for Unicable setups
Replies: 6
Views: 528

Re: DiSEqC on Slave Tuners for Unicable setups

Hi crazycat It's hard to argue with the developer :-), I was just refering to the manual for the 6508 where it says that it is only possible to send diseqc messages on the master tuner. So I did some testing in tvheadend and basically the driver accepts the diseqc message but it seems to never arriv...
by LSD
Thu Nov 03, 2022 4:05 pm
 
Forum: TBS6508 Multi-standard Octa Tuner PCI-e Card
Topic: DiSEqC on Slave Tuners for Unicable setups
Replies: 6
Views: 528

DiSEqC on Slave Tuners for Unicable setups

Hi Basically it makes perfect sense in a legacy LNB environment to allow only the master tuner to send DiSEqC message, but this is not the case for Unicable setups, where the slave tuner must be able to send DiSEqC messages over the same cable. Could the driver be enhanced so that it uses the master...
by LSD
Wed Nov 02, 2022 9:23 pm
 
Forum: TBS6508 Multi-standard Octa Tuner PCI-e Card
Topic: DiSEqC on Slave Tuners for Unicable setups
Replies: 6
Views: 528

Re: Strong Artefacts - Questionable SNR and high BER

for me disabling C6/C7 Support in the BIOS did the trick
by LSD
Tue Dec 16, 2014 9:49 pm
 
Forum: Linux
Topic: Strong Artefacts - Questionable SNR and high BER
Replies: 43
Views: 35319

Re: TBS-Matrix V2.3, do I need a different uboot????

yes indeed, I remembere having seen inode errors on the RO filesystem of OpenElec on my custom compiled build but didn't pay too much attention as I was looking after my network problem.
by LSD
Wed Dec 10, 2014 4:41 am
 
Forum: Install and setup
Topic: TBS-Matrix V2.3, do I need a different uboot????
Replies: 8
Views: 6197

Re: TBS-Matrix V2.3, do I need a different uboot????

well, no luck, tried several methods, uboots..... but never ever was able to access the partition table. So I think I'm gonna send it back tomorrow.
by LSD
Wed Dec 10, 2014 4:21 am
 
Forum: Install and setup
Topic: TBS-Matrix V2.3, do I need a different uboot????
Replies: 8
Views: 6197

Re: TBS-Matrix V2.3, do I need a different uboot????

Thank you for your proposal, I will do that in the evening, although MfgTool2 already fails at trying to create the partition for uboot but it's worth a try.
by LSD
Tue Dec 09, 2014 6:16 pm
 
Forum: Install and setup
Topic: TBS-Matrix V2.3, do I need a different uboot????
Replies: 8
Views: 6197

Re: TBS-Matrix V2.3, do I need a different uboot????

no, nothing at all is connected, so just OTG and power. eMMC = USB storage/disk from the point of view of Windows
by LSD
Tue Dec 09, 2014 12:03 am
 
Forum: Install and setup
Topic: TBS-Matrix V2.3, do I need a different uboot????
Replies: 8
Views: 6197

Re: OpenELEC Beta 4.95.2

yes, I do have revision 2.3, found not much, or lets better say nothing about this revision by now. After trying to test with a original TBS build my eMMC seems to have died (don't know yet if it's just an u-boot problem or if it's really broken, have opened a thread and waiting for a reply). As Rev...
by LSD
Sun Dec 07, 2014 5:58 pm
 
Forum: Announcements
Topic: OpenELEC Beta 4.95.2 and more
Replies: 210
Views: 125690
Next

Return to advanced search