- Code: Select All Code
_____ ____ ____
|_ _| | __ ) | __\
| | | _ \ \_ \
| | | |_) | __) |
|_| |____/ \___/
__ __ _____ ____ _____ ____ __
| \/ | ___ |_ _| /__ \ | _ | /__ \ / |
| |\/| | / _ \ | | __) ) |___ | __) ) | |
| | | | | (_) | _| |_ | __/_ ___| | | __/_ _| |_
|_| |_| \___/ |_____| |____| |_____| |____| |_____|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
*****************************************************************************************
**************** *******************************************************
**************** www.tbsdtv.com *******************************************************
**************** *******************************************************
*****************************************************************************************
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Jun 19 2014 - 18:58:44) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFC60
Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 19 tRCD=7
DRAM CS[0] base 0x00000000 size 512MB
DRAM CS[1] base 0x20000000 size 512MB
DRAM Total size 1GB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is RGMII
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatls **
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatls **
tbs_led off ok
NAND read: device 0 offset 0x100000, size 0x400000
Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.35.14
Created: 2016-04-13 7:15:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4213384 Bytes = 4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC
MOI2921>>
And device does not load.
If I'll reflash kernel (only kernel is enough) device is starting again, but after any power outage issue is back.
Possible workaround is to keep USB drive with kernel connected, so kernel will be reflashed on every boot-up, but is there any proper solution?
I've tried to exchange LR1130 battery (it was dead), but this wasn't the reason.