Setup VDR (Video Disc Recorder)
Posted: Tue Jan 20, 2015 9:39 pm
Hi there, this is my first post here, I have the MOI+ streamer partially set-up, but would like to have it fully set up. So far, I did not find out how to do this, so I start this topic about the setup of VDR.
I have the TBS 6991 buit in. I also have a Canal Digitaal suscription, with two smartcards, and two CAM modules. I also have a Philips 8141 STB where I test the card and dish setup with. This is all working. For the CAM and smartcard to work, I need VDR. The dish has a so called Duo Quad LNB, Duo for the Astra1 and Astra3, and Quad for the four outputs. It is the standard set provided by Canal Digitaal in the Netherlads an other countries iin the Astra1+3 coverage area.
Now, when I scan for channels, I only get results if I only scan Astra1 (19.2e). If I scan for Astra 3 (23.5e) the process finisches, but I can not watch any channel. For testing purposes I use VLC.
My question is; How do I tell VDR to scan for Astra1 and Astra3? And how to tell VDR on which DiSEqC position the satellites are? And, after scanning, how to edit the channels list? I quess it can not be done through the fancy web interface?
So far, this is what I tried already;
To scan for both Astra satellites, I first set the Astra1 in the upper part of the "S-tunning-settings.html" screen and press the "Set DiSEqC" button,
then, I enter the Astra3 in the upper part and press the "Set DiSEqC" button again.
After that, I press the "Scan Channels" button, with "Autoscan" checked. (see both images I uploaded) This process takes a long long time.
After 25 minutes, I get this dialog, and that doesn't make me particularly happy. So, what am I doing wrong here?
I also tried setting the DiSEqC switch port for Astra1 to 0, and Astra3 to 1, but same result. Astra1 is on the first DiSEqC port, and Astra3 on the second. I took in consideration that port 1 sometimes is called port 0. So, why is this not working?
I ssh't into the MOI+. When I run top, I do not see a process called vdr. When I try to run it, I get this error: segmentation fault.
Anyone?
I have the TBS 6991 buit in. I also have a Canal Digitaal suscription, with two smartcards, and two CAM modules. I also have a Philips 8141 STB where I test the card and dish setup with. This is all working. For the CAM and smartcard to work, I need VDR. The dish has a so called Duo Quad LNB, Duo for the Astra1 and Astra3, and Quad for the four outputs. It is the standard set provided by Canal Digitaal in the Netherlads an other countries iin the Astra1+3 coverage area.
Now, when I scan for channels, I only get results if I only scan Astra1 (19.2e). If I scan for Astra 3 (23.5e) the process finisches, but I can not watch any channel. For testing purposes I use VLC.
My question is; How do I tell VDR to scan for Astra1 and Astra3? And how to tell VDR on which DiSEqC position the satellites are? And, after scanning, how to edit the channels list? I quess it can not be done through the fancy web interface?
So far, this is what I tried already;
To scan for both Astra satellites, I first set the Astra1 in the upper part of the "S-tunning-settings.html" screen and press the "Set DiSEqC" button,
then, I enter the Astra3 in the upper part and press the "Set DiSEqC" button again.
After that, I press the "Scan Channels" button, with "Autoscan" checked. (see both images I uploaded) This process takes a long long time.
After 25 minutes, I get this dialog, and that doesn't make me particularly happy. So, what am I doing wrong here?
I also tried setting the DiSEqC switch port for Astra1 to 0, and Astra3 to 1, but same result. Astra1 is on the first DiSEqC port, and Astra3 on the second. I took in consideration that port 1 sometimes is called port 0. So, why is this not working?
I ssh't into the MOI+. When I run top, I do not see a process called vdr. When I try to run it, I get this error: segmentation fault.
Anyone?