Good signal but cannot obtain lock
![Post Post](./styles/tbsdtv/imageset/icon_post_target.gif)
Hello,
I understand I should get status "LF" and indication "FE_HAS_LOCK" for singal 74% (like in similar topic) and I get:
and
My current configuration is:
Please provide some advice, I have spent considerable time trying to find out what is wrong.
The adapter is working fine in a different PC with Win7 and connected to Diseqc. For the above tests I disconnected the Diseqc to reduce the elements that may be faulty.
Regards
I understand I should get status "LF" and indication "FE_HAS_LOCK" for singal 74% (like in similar topic) and I get:
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# ./szap-s2 -a 1 -H -C 34 -c ../hotbird_szap-s2.conf "RAI2"
reading channels from file '../hotbird_szap-s2.conf'
zapping to 2 'RAI2':
delivery DVB-S, modulation QPSK
sat 0, frequency 10992 MHz V, symbolrate 27500000, coderate 3/4, rolloff 0.35
vpid 0x0201, apid 0x028b, sid 0x2140
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
status 01 | signal 74% | snr 0% | ber 0 | unc 0 |
status 01 | signal 74% | snr 0% | ber 0 | unc 0 |
status 03 | signal 74% | snr 0% | ber 0 | unc 0 |
and
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# ./szap-s2 -a 1 -H -c ../hotbird_szap-s2.conf "RTR"
reading channels from file '../hotbird_szap-s2.conf'
zapping to 3 'RTR':
delivery DVB-S, modulation QPSK
sat 0, frequency 11034 MHz V, symbolrate 27500000, coderate auto, rolloff 0.35
vpid 0x0334, apid 0x033e, sid 0x06ac
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
status 01 | signal 74% | snr 0% | ber 0 | unc 0 |
status 03 | signal 74% | snr 0% | ber 0 | unc 0 |
status 01 | signal 74% | snr 0% | ber 0 | unc 0 |
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# cat ../hotbird_szap-s2.conf
RAI1:10992:v:0:27500:512:60:8511
RAI2:10992:v:0:27500:513:651:8512
RTR:11034:v:0:27500:820:830:1708
NI:10930:h:0:27500:512:650:7501
RIK:12111:v:0:27500:782:331:782
My current configuration is:
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# uname -a
Linux srv1 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# dmesg |grep cx23885
[ 9.691151] cx23885 driver version 0.0.2 loaded
[ 9.691193] cx23885 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 9.691490] CORE cx23885[0]: subsystem: 6981:8888, board: TurboSight TBS 6981 [card=30,autodetected]
[ 9.951574] Modules linked in: cx23885(+) cx2341x videobuf_dvb dvb_core bttv(+) v4l2_common videodev v4l1_compat v4l2_compat_ioctl32 nouveau(+) videobuf_dma_sg videobuf_core ir_common ir_core btcx_risc ttm shpchp tveeprom drm_kms_helper drm i2c_algo_bit video x38_edac asus_atk0110 edac_core lp parport raid10 raid456 async_pq async_xor usbhid(+) xor async_memcpy async_raid6_recov hid pata_marvell floppy skge ahci libahci sky2 raid6_pq async_tx raid1 raid0 multipath linear
[ 10.492116] cx25840 2-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[ 11.279967] cx25840 2-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
[ 11.288817] cx23885_dvb_register() allocating 1 frontend(s)
[ 11.289015] cx23885[0]: cx23885 based dvb card
[ 12.138683] DVB: registering new adapter (cx23885[0])
[ 12.168148] cx23885_dvb_register() allocating 1 frontend(s)
[ 12.168320] cx23885[0]: cx23885 based dvb card
[ 12.340081] DVB: registering new adapter (cx23885[0])
[ 12.369570] cx23885_dev_checkrevision() Hardware revision = 0xa5
[ 12.369757] cx23885[0]/0: found at 0000:06:00.0, rev: 4, irq: 19, latency: 0, mmio: 0xfe800000
[ 12.370037] cx23885 0000:06:00.0: setting latency timer to 64
- Code: Select All Code
root@srv1:~/tbs-110818/szap-s2# modinfo tbs6981fe
filename: /lib/modules/2.6.38-11-server/kernel/drivers/media/dvb/frontends/tbs6981fe.ko
license: TurboSight Proprietary: www.tbsdtv.com
author: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
description: TurboSight TBS 6981 Dual DVBS/S2 frontend driver module
depends:
vermagic: 2.6.38-11-server SMP mod_unload modversions
Please provide some advice, I have spent considerable time trying to find out what is wrong.
The adapter is working fine in a different PC with Win7 and connected to Diseqc. For the above tests I disconnected the Diseqc to reduce the elements that may be faulty.
Regards