TBSDTV Community Forum

by **tuksmr** » Mon Aug 15, 2011 6:31 pm

ok. i've installed with this revision. make and make module went ok, but now i have problem with virtual adapter.
when i try to use it , my card can't tune (no signal) even with fta channels.

afrer load dvbloopback module dmesg shows:

Code: Select All Code: modprobe dvbloopback [ 1832.354283] dvb-usb: TBS QBOXS3 DVBS2 USB2.0 successfully initialized and connected. [ 1857.258922] /home/marcin/src/sc/contrib/sasc-ng/dvbloopback/module/dvb_loopback.c: frontend loopback driver v0.0.1 [ 1857.258933] dvbloopback: registering 1 adapters [ 1857.260512] DVB: registering new adapter (DVB-LOOPBACK)

now i'm starting sasc-ng

Code: Select All Code: root@dragon:~# /usr/local/bin/sasc-ng -j 0:1 --cam-budget --cam-dir /etc/sc_files/ --sid-nocache --buffer 8M Aug 15 12:32:11.253 : Version: 0.0.2-e44bd34b6277+ Aug 15 12:32:11.254 CAM: initializing plugin: SoftCam (1.0.0pre-HG-e44bd34b6277+): A software emulated CAM Aug 15 12:32:11.254 CAM(general.info): SC version 1.0.0pre-HG-e44bd34b6277+ initializing (VDR 1.6.0) Aug 15 12:32:11.254 CAM: starting plugin: Aug 15 12:32:11.254 CAM(general.info): SC version 1.0.0pre-HG-e44bd34b6277+ starting (VDR 1.6.0) Aug 15 12:32:11.254 CAM(core.load): ** Plugin config: Aug 15 12:32:11.254 CAM(core.load): ** Key updates (AU) are enabled (active CAIDs) (no prestart) Aug 15 12:32:11.254 CAM(core.load): ** Local systems DON'T take priority over cached remote Aug 15 12:32:11.254 CAM(core.load): ** Concurrent FF recordings are NOT allowed Aug 15 12:32:11.254 CAM(core.load): ** Force transfermode with digital audio Aug 15 12:32:11.254 CAM(core.load): ** ECM cache is set to enabled Aug 15 12:32:11.254 CAM(core.load): ** TsBufferSize is 4 MB Aug 15 12:32:11.254 CAM(core.load): ** ScCaps are 1 2 0 0 0 0 0 0 0 0 Aug 15 12:32:11.277 CAM(general.info): loading cardclient config from /etc/sc_files//cardclient.conf Aug 15 12:32:11.298 CAM(cardclient.newcamd): now using protocol version 525 (cdLen=8) ... Aug 15 12:32:11.298 CAM(cardclient.core): client 'Newcamd' ready Aug 15 12:32:11.323 CAM(core.net): connecting to .... Aug 15 12:32:11.471 CAM(cardclient.login): Newcamd: CaID=0100 adm.... Aug 15 12:32:11.471 CAM(general.info): loading keys from /etc/sc_files//SoftCam.Key Aug 15 12:32:11.471 CAM(core.load): loaded 0 keys from /etc/sc_files//SoftCam.Key Aug 15 12:32:11.471 CAM(general.info): loading smartcard data from /etc/sc_files//smartcard.conf Aug 15 12:32:11.471 CAM(core.load): loaded 0 smartcard data from /etc/sc_files//smartcard.conf Aug 15 12:32:11.471 CAM(general.info): loading cardslot config from /etc/sc_files//cardslot.conf Aug 15 12:32:11.471 CAM(general.info): loading overrides from /etc/sc_files//override.conf Aug 15 12:32:11.491 CAM(core.load): loaded 0 overrides from /etc/sc_files//override.conf Aug 15 12:32:11.491 CAM(general.error): no keys loaded for softcam! Aug 15 12:32:11.491 CAM(core.load): ** registered systems: Aug 15 12:32:11.491 CAM(core.load): ** Cardclient (pri -15) Aug 15 12:32:11.491 CAM(core.load): ** Conax (pri -10) Aug 15 12:32:11.491 CAM(core.load): ** ConstCW (pri -20) Aug 15 12:32:11.491 CAM(core.load): ** Cryptoworks (pri -10) Aug 15 12:32:11.491 CAM(core.load): ** Irdeto (pri -10) Aug 15 12:32:11.491 CAM(core.load): ** Irdeto2 (pri -8) Aug 15 12:32:11.491 CAM(core.load): ** Nagra (pri -10) Aug 15 12:32:11.491 CAM(core.load): ** Nagra2 (pri -10) Aug 15 12:32:11.491 CAM(core.load): ** Fake-NDS (pri -12) Aug 15 12:32:11.491 CAM(core.load): ** SC-Conax (pri -5) Aug 15 12:32:11.491 CAM(core.load): ** SC-Cryptoworks (pri -5) Aug 15 12:32:11.491 CAM(core.load): ** SC-Irdeto (pri -5) Aug 15 12:32:11.491 CAM(core.load): ** SC-Nagra (pri -5) Aug 15 12:32:11.491 CAM(core.load): ** SC-Seca (pri -5) Aug 15 12:32:11.492 CAM(core.load): ** SC-Viaccess (pri -5) Aug 15 12:32:11.492 CAM(core.load): ** SC-VideoGuard2 (pri -5) Aug 15 12:32:11.492 CAM(core.load): ** Seca (pri -10) Aug 15 12:32:11.492 CAM(core.load): ** @SHL (pri -10) Aug 15 12:32:11.492 CAM(core.load): ** Viaccess (pri -10) Aug 15 12:32:12.510 dvr: Starting thread on /dev/dvb/adapter1/dvr1 The thread scheduling parameters indicate: policy = 1 priority = 99 Aug 15 12:32:12.510 demux: Starting thread on /dev/dvb/adapter1/demux1 The thread scheduling parameters indicate: policy = 0 priority = 0 Aug 15 12:32:12.510 frontend: Starting thread on /dev/dvb/adapter1/frontend1 The thread scheduling parameters indicate: policy = 0 priority = 0 Aug 15 12:32:12.510 : Listening on port 5456

it seems started. could you tell me if this is proper start of sasc-ng?

im trying start FTA channel:

Code: Select All Code: marcin@dragon:~$ szap -a 1 '4fun.TV(CYFRA +)' reading channels from file '/home/marcin/.szap/channels.conf' zapping to 890 '4fun.TV(CYFRA +)': sat 0, frequency = 10719 MHz V, symbolrate 27500000, vpid = 0x00a3, apid = 0x005c sid = 0x1134 using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'

and silen. nothing is going on

(i pressed ctrl+c)

dmesg shows (only ones, the first time):

Code: Select All Code: [ 2138.636105] dvblb_fake_ioctl interrupted: 4 [ 2140.880210] TurboSight TBS 5921 Frontend: [ 2140.880212] tbs5921fe: software version is 1.24.2 [ 2140.880215] TurboSight TBS 5921 Frontend: [ 2140.880216] tbs5921fe - Successfully Initialized

When i try to shap scrambled channell it's the same as with the fta channel - silent

ans sasc-ng log (in this case on console) is silent too

if i try to run kaffeine with runnig sasc-ng then kaffeine is hanging

and won't start

if i disable sasc-ng and try tu run kaffeine, its says:

Code: Select All Code: kaffeine(17673) DvbLinuxDevice::identifyDevice: couldn't open "/dev/dvb/adapter1/frontend0" kaffeine(17673) DvbLinuxDevice::identifyDevice: couldn't identify device

why i cannot tune card on virtual dvb? or what do i wrong still?

Code: Select All Code: root@dragon:/dev/dvb# ll adapter1/ razem 0 drwxr-xr-x 2 root root 280 2011-08-15 14:42 ./ drwxr-xr-x 4 root root 80 2011-08-15 14:42 ../ crw-rw----+ 1 root video 212, 12 2011-08-15 14:42 audio0 crw-rw----+ 1 root video 212, 13 2011-08-15 14:42 audio1 crw-rw----+ 1 root video 212, 6 2011-08-15 14:42 demux0 crw-rw----+ 1 root video 212, 7 2011-08-15 14:42 demux1 crw-rw----+ 1 root video 212, 8 2011-08-15 14:42 dvr0 crw-rw----+ 1 root video 212, 9 2011-08-15 14:42 dvr1 crw-rw----+ 1 root video 212, 4 2011-08-15 14:42 frontend0 crw-rw----+ 1 root video 212, 5 2011-08-15 14:42 frontend1 crw-rw----+ 1 root video 212, 14 2011-08-15 14:42 osd0 crw-rw----+ 1 root video 212, 15 2011-08-15 14:42 osd1 crw-rw----+ 1 root video 212, 10 2011-08-15 14:42 video0 crw-rw----+ 1 root video 212, 11 2011-08-15 14:42 video1

it seems i've no access to virtual card
but chmod o+rw change nothing

maybe my card (tbs5921) can not support virtual dvb ? anybody knows?

by **piotrekfronc** » Tue Aug 16, 2011 12:36 am

Make sure mutex patch is applied for drivers linux tree (apps should hang on device if it is not applied, in "forever loop"). Kill all kaffeine processes to release device (find it with ps -ef|grep kaff ).
DONT use kaffeine 1+, use only kaffeine 0.8x versions (best testing would be with gxine).

by **tuksmr** » Tue Aug 16, 2011 1:23 am

piotrekfronc Wrote:Make sure mutex patch is applied for drivers linux tree (apps should hang on device if it is not applied, in "forever loop").

It was that.
i applied patch to previously installed tbs drivers.
this time i downloaded tbs drivers to other directory, applied patch and installed. and it's worked

by **tuksmr** » Fri Aug 26, 2011 12:33 am

piotrekfronc Wrote:
Code: Select All Code
sudo apt-get install build-essential devscripts mercurial

this is also necesarily

Code: Select All Code: sudo aptitude install libssl-dev gettext

by **Vojta1** » Mon Oct 17, 2011 12:17 am

Hi,
does anyone tried to install sasc-ng on Ubuntu 11.10 with kernel v. 3? Do you think I can use above tutorial for it as well? Do I still need to patch the drivers?
Thanks
Vojta

by **piotrekfronc** » Sat Oct 22, 2011 2:00 am

Works well

by **dulcet** » Tue Oct 25, 2011 12:51 am

hi
everybody

does anybody successfully installed & working sasc-ng R 600 on Ubuntu 11.10 with kernel 3.0.x ?

i done install successfully but didn't sync with DVBLOOPBACK with Real Adapter

dulcet

by **piotrekfronc** » Sun Dec 11, 2011 8:14 pm

Make sure you have CLEAN installation. It works perfect for me with 3.X kernels.

TBSDTV Community Forum

sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Re: sasc-ng with Ubungu 11.04

Who is online