Moderator Control Panel ]

Blindscan with tbs 6909

News and information about TBS products.

Blindscan with tbs 6909

Postby Geraldo » Sun Aug 09, 2020 3:20 am

Hello, I want to buy a tbs 6909 card, to use with windows 10. I know it is an octa turner card. I ask if I use only one input from it, I can tune all the frequencies of a given satellite, in V and H, doing blindscan, of the chosen satellite. I hope someone helps me, I live in Brazil and I'm using a translator. Thank you
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm

Re: Blindscan with tbs 6909

Postby Geraldo » Sun Aug 09, 2020 11:35 pm

I wonder if anyone can tell me if I can use a C or Ku band antenna on input 0, and tune all transponders in polarization V and H. I already have the tbs 8922 card, I can't get it to work with windows 10 64 bit, Gigabyte B250m-d3h motherboard. It has a signal, but it does not save the frequencies. On the tbs 8922 ts capture it says "There are no drivers installed for this device". I've read everything on the tbs forum and it doesn't have a solution until today, it works with some and the other doesn't. And this is how it is today.
If anyone managed to help me I appreciate it. Here in Brazil I found no forum to help me. Thank you
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm

Re: Blindscan with tbs 6909

Postby Geraldo » Mon Aug 10, 2020 4:55 am

P_20200809_163319_vHDR_On[1].jpg
TBS 8922 TS CAPTURE
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm

Re: Blindscan with tbs 6909

Postby steven » Tue Aug 11, 2020 9:22 am

Hi Sir

6909 do not support blindscan , and only one cable can not scan all transponder ,if you are using ku dual band you need 4 input VL VH HL HH

if you are usng C band 5150 you need two input VL and HL

For 8922 issue you can setup a remote send remote information to our support we will have a remote check

Thanks

Kind Regards

steven
steven
 
Posts: 2239
Joined: Fri Aug 06, 2010 3:23 pm

Re: Blindscan with tbs 6909

Postby Geraldo » Tue Aug 11, 2020 6:38 pm

Steven, thanks for responding. But I still don't understand about the ku and c band for tbs 6909. In the ku band do I have to connect four cables to the tbs 6090 board? But my lnbf ku only has a cable outlet. And the band lnbf also has only one cable outlet. I have a diseqc key with four inputs and an output. If you can explain it in more detail I would appreciate it. And as for the tbs 8922 card, how do I configure it for remote information.
Sorry for the writing I am using a translator. Thank you
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm

Re: Blindscan with tbs 6909

Postby steven » Wed Aug 12, 2020 9:09 am

hi sir

you can send email to our support , take one picture of your LNB let us check it is C or ku dual band .

For 8922 you can setup teamview remote .

Thanks

Kind Regards

steven
steven
 
Posts: 2239
Joined: Fri Aug 06, 2010 3:23 pm

Re: Blindscan with tbs 6909

Postby Geraldo » Wed Aug 12, 2020 10:05 pm

Ok Steven, I already have the teamviewer installed on the PC for remote access to see the tbs 8922 card.
And you are going to do the access or do I have to ask for support?
You have to make an appointment, because I work from 6am until 6pm.
Today I'm home until 9pm, then I'll be home, Saturday, Sunday and Monday. I don't know what time zone. I live in Florianópolis, Santa Catarina Brazil. Thank you
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm

Re: Blindscan with tbs 6909

Postby Geraldo » Thu Aug 13, 2020 5:26 am

CM200812-180751001.jpg
Lnb Banda ku

I sent a message to support, about tbs 8922.
The lnb, band c has only one output, and is a single point. I didn't take a picture because here it is raining today.
Thank you
Geraldo
 
Posts: 6
Joined: Mon Jun 22, 2020 7:02 pm


Return to News

Who is online

Users browsing this forum: No registered users and 4 guests