TBSDTV Community Forum

Well, i test last windows driver (1.0.1.2) on Windows 7 (x64). And i see only 4 tv channels from 8. So, i think multiPLP not working on Windows too (Novosibirsk, Russia).

how you test MultiPLP ? ProgDVB, DVBDream OEM?

you enter proper PLP ID on manual scan ? PLP 0,1,2,3 (used 0 and 1)

crazycat wrote:how you test MultiPLP ? ProgDVB, DVBDream OEM?

you enter proper PLP ID on manual scan ? PLP 0,1,2,3 (used 0 and 1)

I use tbsviewer_v20121130.zip
I don't understand how to set PLP ID in this programm.

I will try dvbdream_v22d_oem.zip and progdvb-tbs_6.91.4.zip today, but later.

orekhovav wrote:

crazycat wrote:how you test MultiPLP ? ProgDVB, DVBDream OEM?

you enter proper PLP ID on manual scan ? PLP 0,1,2,3 (used 0 and 1)

I use tbsviewer_v20121130.zip
I don't understand how to set PLP ID in this programm.

I will try dvbdream_v22d_oem.zip and progdvb-tbs_6.91.4.zip today, but later.

Well, i try dvbdream_v22d_oem.zip (automatic scan and manual scan (i not found any PLP settings)) and progdvb-tbs_6.91.4.zip (automatic scan).

The result is - NO MultiPLP, i see only 4 tv channels from 8 tv channels.

And one more thing: i do device delete/driver re-install, i do rebooting, but this dont help

You must install latest drivers (TBS6220, TBS6280, TBS6284, TBS5880 and TBS5220)

Multistream (MultiPLP for DVB-T2) supported in all ProgDVB 6.91.4+ (Standard, Pro, OEM).
You must setup device, select Channel List -> Manual Scan and select desired channel number (freq in KHz) and bandwidth (8MHz), press Lock. IF signal locked - enable Multistream checkbox and press Detect button - all available PLP nums must be detected and available for selection in combobox. Next select desired PLP (0,1), press Lock and Scan.

In auto-scan mode all available PLPs must be scanned (not tested).

I can try this on monday, march 18.
One more question: i use last windows driver (1.0.1.2) for 6220, and i use progdvb-tbs_6.91.4.zip (last from this site downloads). It is correct versions for MultiPLP?

ProgDVB OEM is same as ProgDVB Standard.

9.91.4 is first version with MultiPLP support, must work.

Well, results of test:
(I try progdvb-tbs_6.91.4.zip and 6.92.3 (latest from official site))
After signal locked and 'multistream' enabled and PLPs detected, we have 0,1,2,3,All in combo box. If i choose 0 in combo box, i have 4 tv channels and 3 radio channels. If i choose 1, i have 4 tv channels and 3 radio channels (same channels, as for 0 PLP ID).
If i choose 2, i have 4 tv channels and 3 radio channels (same channels, as for 0 PLP ID). If i choose 3, i have 4 tv channels and 3 radio channels (same channels, as for 0 PLP ID). If i choose 'All', i have four copies of this channels list (4 tv channels and 3 radio channels).
I think, this may be a driver bug - for each PLP ID returned channels list from 0 PLP ID.
Can you check this?

I try choose 1 PLP ID after programm start, without trying 0 PLP ID (in hope, that i see other 4 tv channels), but scan was found only channels from 0 PLP ID.
Hack not working