MOI & CAM & oscam

[eesdil]

i hope that this is what I should see:

# gnutv -adapter 0 -channels /tmp/channels.conf -out dvr 'Nova'
Using frontend "TurboSight TBS 2990 DVBS/S2 frontend", type DVB-S
status SCVYL | signal 7d57 | snr ffff | ber 03ffffff | unc 00000000 | FE_HAS_LOCK
en50221_tl_handle_sb: Received T_SB for connection not in T_STATE_ACTIVE from module on slot 00

en50221_stdcam_llci_poll: Error reported by stack:-7

CAM Application type: 01
CAM Application manufacturer: cafe
CAM Manufacturer code: babe
CAM Menu string: Irdeto Access
CAM supports the following ca system ids:
0x0fff
Received new PMT - sending to CAM...

thanks

[gfi]

CAM supports the following ca system ids:
0x0fff - it's not good, but maybe isn't important.

In attachment, little tool (isn't optimized for demux buffer size used in kernel of MOI), what sending dvr over net.

Place in tmp, run
./netdvr-moi0

-----
Star vlc and network stream:
http://<ip_of_your_moi>:34339/0

You need to have also gnutv running, of course.
Look, if is stream descrambled. Wait approx. 3min. Hope You have activated card.

[eesdil]

I am not sure I am doing it right as nothing is happening.
Attaching the screen how I did.

thanks

[gfi]

IP is 192.168.1.188, not 192.168.188

[eesdil]

good point, it explains...

But now I cannot scan the channels as it doesnt find anything.
getting error message, maybe thats the problem:

[ 5788.835000] TurboSight TBS 299X Frontend:
[ 5788.835000] tbs299xfe - modulation 6 is not supported

Anyway as I am able to get some channels will post.

[gfi]

good point, it explains...

But now I cannot scan the channels as it doesnt find anything.
getting error message, maybe thats the problem:

[ 5788.835000] TurboSight TBS 299X Frontend:
[ 5788.835000] tbs299xfe - modulation 6 is not supported

Anyway as I am able to get some channels will post.

You need to scan without CI module insered, also You can use scan only, as right.
Meaning scan, not scan-s2.

Your Line of channel need to looks like that:
<channel_name>:<frequency>:<pol h or v>:0:<symbol_rate>:<video_pid>:<audio_pid>:<service_id>:6
(will be upgraded, scan application)

Edit Your Satellite file (Astra 3...) before start scanning. You need to have an actual config.

[eesdil]

hi,

this is what i have
Nova:12070:h:0:27500:3201:3202:13138:5

But I didnt get anything back. It started to do something, but... here is the outcome:
from netdvr-moi0

Starting STREAM thread keeper, tid 157
listenfd 3
fd 3 has events 1
new connection, fd 4
Starting LIVE STREAM thread, fd 4
stream: got GET /0 HTTP/1.1

New pid: 0x0
dmx_cs.cpp:cDemux - num=1
dmx_cs.cpp:Open - pes_type=DMX_TP_CHANNEL hVideoBuffer= uBufferSize=186496
DMX_SET_SOURCE failed(Invalid argument)dmx_cs.cpp:pesFilter (type=DMX_TP_CHANNEL) - Pid=0
dmx_cs.cpp:pesFilter ok
dmx_cs.cpp:Start (type=DMX_TP_CHANNEL) Pid 0
ok

en50221_stdcam_llci_poll: Error reported by stack:-3

I am not sure this is good or bad.

thanks

[gfi]

hi,

this is what i have
Nova:12070:h:0:27500:3201:3202:13138:5

But I didnt get anything back. It started to do something, but... here is the outcome:
from netdvr-moi0

Starting STREAM thread keeper, tid 157
listenfd 3
fd 3 has events 1
new connection, fd 4
Starting LIVE STREAM thread, fd 4
stream: got GET /0 HTTP/1.1

New pid: 0x0
dmx_cs.cpp:cDemux - num=1
dmx_cs.cpp:Open - pes_type=DMX_TP_CHANNEL hVideoBuffer= uBufferSize=186496
DMX_SET_SOURCE failed(Invalid argument)dmx_cs.cpp:pesFilter (type=DMX_TP_CHANNEL) - Pid=0
dmx_cs.cpp:pesFilter ok
dmx_cs.cpp:Start (type=DMX_TP_CHANNEL) Pid 0
ok

en50221_stdcam_llci_poll: Error reported by stack:-3

I am not sure this is good or bad.

thanks

Forget about that.
If You don't understand for a simple steps, what I wrote, hardly any discusion.

[eesdil]

excuse me, but please if you could explain me what I did wrong?
thanks

[gfi]

excuse me, but please if you could explain me what I did wrong?
thanks

nothing. You're only need doing, what I wrote above.
I need to know, Your CAM working (You have a descreambled stream on vlc...) or not.

If not, there's no way as to help You, If Yes, all is OK and we can continue.

Just send me info, channel is descrambled in stream and I create complete faq with instructions (also for other users with paired and one-stream CAMs).
Also applications, of course.

Don't worry about info, like You sent (modulation isn't supported), just use scan, instead of scan-s2 command.
Parameters are some as in scan-s2 sample.

Control Initialization of Your CI with 'dmesg' command, after inserting CAM to MOI.