Moderator Control Panel ]

MuMuDvb - Configuration

What software to use? Good question, do some digging here and find the best one for you.

MuMuDvb - Configuration

Postby Streamer » Sat Feb 01, 2014 2:03 am

Hello,

I have problem with configuration MuMuDvb.

In the first step I run "scan" and I have got :
Code: Select All Code
4fun.TV:10719:v:0:27500:163:92:4404

4fun.TV                  (0x1134) 01: PCR == V   V 0x00a3 A 0x005c (pol) TT 0x0204



Szap :

Code: Select All Code
zapping to 34 '4fun.TV':
sat 0, frequency = 10719 MHz V, symbolrate 27500000, vpid = 0x00a3, apid = 0x005c sid = 0x1134
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
status 1f | signal 86a7 | snr df91 | ber 03ffffff | unc 00000000 | FE_HAS_LOCK
status 1f | signal c69b | snr 5709 | ber 03ffff00 | unc 00000000 | FE_HAS_LOCK
status 1f | signal c6db | snr d39f | ber 00000000 | unc 00000000 | FE_HAS_LOCK


MuMuDvb.conf :


Code: Select All Code
card=0
freq=10719
pol=v
srate=27500

common_port=1234

multicast_ttl=10

ip=46.41.XXX.XXX
#ip=127.0.0.1
port=1234
name=4Fun.TV - Stream
service_id=92
pids= 4404
#cam_pmt_id = 4404





On 46.41.XXX.XXX netcat :

Code: Select All Code
nc -l -p 1234




Code: Select All Code
MuMuDVB Version 1.7.2
 --- Build information ---
Built with CAM support.
Built with SCAM support.
Built without transcoding support.
Built with ATSC support.
Built with ATSC long channel names support.
Built with support for DVB API Version 5.2.
---------
Originally based on dvbstream 0.6 by (C) Dave Chapman 2001-2004
Released under the GPL.
Latest version available from http://mumudvb.braice.net/
Project from the cr@ns (http://www.crans.org)
by Brice DUBOST (mumudvb@braice.net)

Info:  SAP:  Sap announces will be sent
Info:  Main:  ========== End of configuration, MuMuDVB version 1.7.2 is starting ==========
Info:  Main:  Streaming. Freq 10719000
Info:  Tune:  Using DVB card "TurboSight TBS 2990 DVBS/S2 frontend" tuner 0
Info:  Tune:  Tuning DVB-S to Freq: 969000 kHz, LO frequency 9750000 kHz Pol:V Srate=27500000, LNB number: 0
Info:  Tune:  LNB voltage 13V
Info:  Tune:  DISEQC SETTING SUCCEDED
Info:  Tune:  FE_STATUS:
Info:  Tune:  FE_STATUS:
Info:  Tune:       FE_HAS_SIGNAL : found something above the noise level
Info:  Tune:       FE_HAS_CARRIER : found a DVB signal
Info:  Tune:       FE_HAS_VITERBI : FEC is stable
Info:  Tune:       FE_HAS_SYNC : found sync bytes
Info:  Tune:       FE_HAS_LOCK : everything's working...
Info:  Tune:  Event:  Frequency: 10719000 (or 8781000)
Info:  Tune:          SymbolRate: 27500000
Info:  Tune:          FEC_inner:  5
Info:  Tune:  Bit error rate: 67108608
Info:  Tune:  Signal strength: 30422
Info:  Tune:  SNR: 54175
Info:  Tune:  FE_STATUS:
Info:  Tune:       FE_HAS_SIGNAL : found something above the noise level
Info:  Tune:       FE_HAS_CARRIER : found a DVB signal
Info:  Tune:       FE_HAS_VITERBI : FEC is stable
Info:  Tune:       FE_HAS_SYNC : found sync bytes
Info:  Tune:       FE_HAS_LOCK : everything's working...
Info:  Main:  Card 0, tuner 0 tuned
Info:  Main:  Diffusion 1 channel
Info:  Main:  Channel number :   0, name : "4Fun.TV - Stream"  service id 92
Info:  Main:    Multicast4 ip : 46.41.XXX.XXX:1234



And now MuMu is "frozen" and don't send any packets but streaming timer works correctly because after exit I see :

Code: Select All Code
^CInfo:  Main:  End of streaming. We streamed during 0d 0:02:11
Info:  Main:  Caught signal 2 - closing cleanly.
Info:  Main:  ========== MuMuDVB version 1.7.2 is stopping with ExitCode 0 ==========


Connection from MOI to 46.41.XXX.XXX is available on this port, but I also tested it on 127.0.0.1.

What is wrong ?


Best Regards
Streamer
 
Posts: 1
Joined: Fri Jan 31, 2014 8:26 pm

Return to Software

Who is online

Users browsing this forum: No registered users and 1 guest