TBS 5922 WMC 7 32 bit - No Signal (OK Now)

[mrm2k10]

Hi,

I'm using TBS5922 Card on Windows 7 32 bit (Ultimate Edition - Fully Updated). I installed Latest Drivers from Site and the Box works without problem with DVBdream.But when i tried to set it up in Windows Media Center 7,i received no Signal. I have a switch and 2 Universal Ku LNBs on Port 2 & 3. i configured them and when i try to scan (Single or Full trasponder Scan - doesn't matter) it finds nothing (No signal).

Does any one has any solution for This?

[mrm2k10]

Hello again,

Update
After restarting windows , there wa some sort of improvement : (I use a 4-port switch with NileSat on Port 2 & Hotbird on Port 3 . I should say again : in ProgDVB & DVBdream there is no problem.)

i used single Transponder scan and used the Best Transponder in Nilesat (according to Signal Power & quality in dvbdream). when i entered the FREQ , Synbol Rate and polarization, and waited 2 seconds,it showed a green bar "(Singnal Qaulity) and lock indicator on the unit was ON. but it wasn't stable ,after 1 second lock indicator started to blink and the Signal Quality bar started to jump between green and yellow . i hit the Next to start scan , Lock indicator was ON (Green LED on the box)and stable , but no channels found. i think there is some sort of Communication Problem between WMC and the Box.

[CasioJones]

there also "might" be a problem with 64 bit drivers as well. but only with windows 7 version. I got this as soon as it was available.
Not long after install i started getting blue screens. So resinstalled windows from scratch. Same problem kept re-occuring for me.

So i instead switched to 32Bit vista , only had problems with dvbdream since. Now i just need to find a program what will work with the remote without having to figure out winrc.
It may be a problem related to my motherboard not being normal ( asus E35M1M_PRO) , but since it's stable on vista i doubt that at all.

hope this helps
chris

[mrm2k10]

there also "might" be a problem with 64 bit drivers as well. but only with windows 7 version. I got this as soon as it was available.
Not long after install i started getting blue screens. So resinstalled windows from scratch. Same problem kept re-occuring for me.

So i instead switched to 32Bit vista , only had problems with dvbdream since. Now i just need to find a program what will work with the remote without having to figure out winrc.
It may be a problem related to my motherboard not being normal ( asus E35M1M_PRO) , but since it's stable on vista i doubt that at all.

hope this helps
chris

Hi ,

I'm using Windows 7 Ultimate 32bit version ,so i'm not using 64 bit drivers.

[steven]

Hi
Would mind try new Driver.you can download on our download page. version:2.0.1.5
Thanks

[CasioJones]

re-installing windows as we speak , should have feed back in a day or 2 with i try different versions of windows.

Ty
Chris

[steven]

re-installing windows as we speak , should have feed back in a day or 2 with i try different versions of windows.

Ty
Chris

Hi CasioJones
Is it ok now ?
thanks

[CasioJones]

sorry for not updating since , other r/l problems distracted me.
from the looks of it - it's all good now.
Ty for the help

[Dazob]

I have exactly the same problems with the current Version V2.0.2.1.
After going back to the version that was on my CD (V2.0.1.6) it works now.

[patmos]

Same issue here. Low or no signal with latest TBS driver version. The driver on the CD (v 2.0.1.6)works well with DVBdream. It cannot do diseqc 1.0 switching for ProgDvb. I cannot use Windows Media Centre. I'm on Win7 32 bit.