Yes, IR receiver is the black thing glued on USB bracket. Don't know where it's connected, I will have a look when go back home.
Thanks for the step by step
mikebzh44 Wrote:So I MUST write u-boot to eMMC with Peter's instructions but in this thread, u-boot-matrix.imx is written on SD card, not on eMMC.
If someone can summerize all operations, step by step, it would be great :
1 - Install MatrixTV 1.0.1.0
2 - Overwrite u-boot to eMMC (How ? From which archive ? ...)
3 - Install OE on SD cart (How ? From which tuto ? ...)
4 - Need to overwrite some file on SD card (Which ? Where source and target files are located ? ...)
Thanks.
vpeter Wrote:mikebzh44, for your IR trouble you can try thisand then reboot the box.
- Code: Select All Code
curl -o /storage/.config/lircd.conf https://dl.dropboxusercontent.com/u/8224157/public/matrix/tbsnec32.conf
But I'm wondering which IR receiver do you use? The one on matrix system or something else?
MatrixELEC:~/.config # for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done
input0: Rx504B Ver:1.00
input1: Rx504B Ver:1.00
input2: gpio_ir_recv
input3: MCE IR Keyboard/Mouse (gpio-rc-recv)
MatrixELEC:~/.config # ps -aef |grep xbmc
954 root 1:20 /usr/lib/xbmc/xbmc.bin --standalone -fs --lircdev /run/lirc/lircd --debug
1068 root 0:00 grep xbmc
MatrixELEC:~/.config # cat /run/lirc/lircd
cat: can't open '/run/lirc/lircd': No such device or address
lsusb -v
MatrixELEC:~ # for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done
input2: gpio_ir_recv
input3: MCE IR Keyboard/Mouse (gpio-rc-recv)
MatrixELEC:~ # for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done
input2: gpio_ir_recv
input3: MCE IR Keyboard/Mouse (gpio-rc-recv)
input5: Rx504B Ver:1.00
input6: Rx504B Ver:1.00
[root@matrixtv ~]# for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done
input0: gpio-keys
input1: rc-core loopback device
input2: Rx504B Ver:1.00
input3: Rx504B Ver:1.00
[root@matrixtv ~]# for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done
input0: gpio-keys
input1: rc-core loopback device
input2: Rx504B Ver:1.00
input3: Rx504B Ver:1.00
echo "blacklist gpio_ir_recv" >>/storage/.config/modprobe.d/blacklist.conf
[root@matrixtv ~]# ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event1) with:
Driver rc-loopback, table rc-empty
Supported protocols: NEC RC-5 RC-6 JVC SONY LIRC RC-5-SZ
Enabled protocols: LIRC
Repeat delay = 1000 ms, repeat period = 125 ms
Use standard location /etc/modprobe.d/blacklist.conf. And module name is lirc_matrix (I think).mikebzh44 Wrote:Is there a way to blacklist this receiver in MatrixTV (because /storage does not exist) or to force good one (lirc1) ?
Users browsing this forum: No registered users and 3 guests