Moderator Control Panel ]

TBS6909 QUATTRO TVHeadend: No Channels

TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Mon Jan 06, 2020 5:48 am

Hi,

i just bought a 6909 to replace my former dual tuner card. I do have a fully working cabeling / setup from the former card but now with this one i get no channels. I want to watch Astra 19.2E and i have following Multiswitch: Unicable Multischalter INVERTO Black IDLP-UST111-CUO10-8PP (8 Unicable-Umsetzungen/SatCR + 1x Legacy-Ausgang)

I followed all the steps from the manual.
Here is some output:

Code: Select All Code
cat /etc/modprobe.d/mxl58x.conf
options mxl58x mode=0


I use this driver: media_build-2019-06-27.tar.bz2
because the lastest fails to build. Already documented here: https://github.com/tbsdtv/linux_media/issues/178

Code: Select All Code
uname -a
Linux 4.9.0-11-amd64 #1 SMP Debian 4.9.189-3+deb9u2 (2019-11-11) x86_64 GNU/Linux


Code: Select All Code
[   34.027492] Hydra FW alive
[   34.088944] chipID=00000001
[   34.090831] chipVer=00000002
[   34.092554] FWVer=0202010a
[   34.132660] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 0 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.132936] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.255626] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:01
[   34.255656] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 1 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.255914] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.380665] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:02
[   34.380695] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 2 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.380951] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.504678] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:03
[   34.504708] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 3 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.504930] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.624769] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:04
[   34.624799] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 4 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.624998] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.744512] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:05
[   34.744542] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 5 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.744753] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.869103] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:06
[   34.869132] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 6 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.869416] dvbdev: DVB: registering new adapter (TBSECP3 DVB Adapter)
[   34.992581] TBSECP3 driver 0000:01:00.0: MAC address 00:22:ab:91:11:07
[   34.992611] TBSECP3 driver 0000:01:00.0: DVB: registering adapter 7 frontend 0 (TurboSight TBS 6909 DVB-S/S2 )...
[   34.992819] TBSECP3 driver 0000:01:00.0: TurboSight TBS 6909 DVB-S/S2 : PCI 0000:01:00.0, IRQ 55, MMIO 0xfe600000


Code: Select All Code
2020-01-05 22:35:33.297 subscription: 0002: "epggrab" subscribing to mux "10988V", weight: 4, adapter: "TurboSight TBS 6909 DVB-S/S2  #6 : DVB-S #0", network: "Astra TBS", service: "Raw PID Subscription"
2020-01-05 22:35:43.280 mpegts: 10988V in Astra TBS - scan no data, failed
2020-01-05 22:37:32.241 subscription: 0002: "epggrab" unsubscribing
2020-01-05 22:38:27.360 mpegts: 10988V in Astra TBS - tuning on TurboSight TBS 6909 DVB-S/S2  #0 : DVB-S #0
2020-01-05 22:38:27.376 subscription: 0003: "scan" subscribing to mux "10988V", weight: 6, adapter: "TurboSight TBS 6909 DVB-S/S2  #0 : DVB-S #0", network: "Astra TBS", service: "Raw PID Subscription"
2020-01-05 22:38:37.360 mpegts: 10988V in Astra TBS - scan no data, failed
2020-01-05 22:38:37.360 subscription: 0003: "scan" unsubscribing
2020-01-05 22:38:38.361 mpegts: 10988V in Astra TBS - tuning on TurboSight TBS 6909 DVB-S/S2  #0 : DVB-S #0
2020-01-05 22:38:38.361 subscription: 0004: "epggrab" subscribing to mux "10988V", weight: 4, adapter: "TurboSight TBS 6909 DVB-S/S2  #0 : DVB-S #0", network: "Astra TBS", service: "Raw PID Subscription"

1.png
2.png
3.png
4.png
5.png


What am i doing wrong?
Thanks in advance
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby daowei » Mon Jan 06, 2020 11:49 am

Hi,
Signal, It's Unicable or Multiswitch(Dish---multiswitch) now? TBS6909 is an advanced tuner card, and have 3 modes for different signal/source.

For Multiswitch, please use mode 1:
# vi /etc/modprobe.d/mxl58x.conf
options mxl58x mode=1

for Unicable, please use mdoe 2:
# vi/etc/modprobe.d/mxl58x.conf
options mxl58x mode=2
and signal must connects to the 4th port, which is far away from PCIE interface.

this is my Skype: daowei23lily@163.com, i can set a remote to check it.


Thanks
daowei
 
Posts: 107
Joined: Fri Aug 12, 2016 6:17 pm

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby daowei » Mon Jan 06, 2020 2:15 pm

Hi,
Again.
For this tuner card, if it's DVBS2 transponder, the "modulation" must be set to "PSK/8".

Thanks
daowei
 
Posts: 107
Joined: Fri Aug 12, 2016 6:17 pm

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Mon Jan 06, 2020 5:22 pm

Hi,

it is Multiswitch with the cables connected: HH, VH,..
I Set the mode to 0 according to the documentation.
Modulation is set correctly.

Will add you later in skype.

Thank you
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby daowei » Tue Jan 07, 2020 9:32 am

Hi,
Ok.
How many satellites your Mulitswitch support? and signal is connected to Multiswitch group 1 (SAT A)?
HH and VH (pol. H and high band; pol.V and high band), fre.> 11700000 belongs to high band.

Thanks
daowei
 
Posts: 107
Joined: Fri Aug 12, 2016 6:17 pm

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Tue Jan 07, 2020 3:16 pm

I have only one Sattelite connected, it is a quattro LNB.
So i have this cabeling:
1.PNG
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby steven » Tue Jan 07, 2020 4:26 pm

Hi Sir

If your LNB is quattro LNB make sure the 4 cables put the right port not like quad LNB you can direct use .
your 4 cable should be VL VH HL HH need to put the right position

Thanks

Kind Regards

steven
steven
 
Posts: 2058
Joined: Fri Aug 06, 2010 3:23 pm

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Tue Jan 07, 2020 4:34 pm

Hi Steven,

thank you for your help. I checked teh cables and they should be fine. I think something is wrong in my config of TvH. Do i have to follow the steps 7.4-7.11 from the manual (Advanced tuner/ Mux config etc) or is this just for a quad LNB?

Best regards
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Wed Jan 08, 2020 5:49 am

I completely redid the whole steps from the manual, and also changed the cabeling in order to try it with unicable (even if this is not what i plan to do). I set the mode to "2" for this and tried both, TVHeadend and minisatip. Nothing is working, it is frustrating :(

I get this in the log (a lot):
Code: Select All Code
[   96.635169] TBSECP3 driver 0000:01:00.0: DVB: adapter 1 frontend 0 frequency 0 out of range (300000..2350000)
[   96.647205] TBSECP3 driver 0000:01:00.0: DVB: adapter 0 frontend 0 frequency 0 out of range (300000..2350000)
[  125.291353] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  126.299921] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  127.296169] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  128.299017] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  129.301586] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  130.304989] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  131.309584] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  132.311020] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  133.313660] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  134.327964] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
[  135.337932] i2c i2c-5: freq=1078000000 delsys=0 srate=41250000
...
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Re: TBS6909 QUATTRO TVHeadend: No Channels

Postby bolzerrr » Wed Jan 08, 2020 6:28 am

PS i dont have the exta Power cable connected because of was missing. But i assume it is Not needed
bolzerrr
 
Posts: 28
Joined: Wed Nov 20, 2013 5:36 am

Next

Return to DVB-S2 Octa Tuner PCIe Card TBS6909

Who is online

Users browsing this forum: No registered users and 6 guests

cron