I knew I'd have to recompile and install the drivers as I've done a number of times in the past.
Followed the procedure in the README as I normally would and the drivers don't install.
This is the output from "dmesg | grep cx23885"
- Code: Select All Code
[ 10.620879] cx23885 driver version 0.0.3 loaded
[ 10.620904] cx23885 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.620906] cx23885[0]: Your board isn't known (yet) to the driver.
[ 10.620907] cx23885[0]: Try to pick one of the existing card configs via
[ 10.620908] cx23885[0]: card=<n> insmod option. Updating to the latest
[ 10.620908] cx23885[0]: version might help as well.
[ 10.620909] cx23885[0]: Here is a list of valid choices for the card=<n> insmod option:
[ 10.620911] cx23885[0]: card=0 -> UNKNOWN/GENERIC
[ 10.620912] cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp
[ 10.620913] cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800
[ 10.620914] cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250
[ 10.620915] cx23885[0]: card=4 -> DViCO FusionHDTV5 Express
[ 10.620916] cx23885[0]: card=5 -> Hauppauge WinTV-HVR1500Q
[ 10.620917] cx23885[0]: card=6 -> Hauppauge WinTV-HVR1500
[ 10.620918] cx23885[0]: card=7 -> Hauppauge WinTV-HVR1200
[ 10.620919] cx23885[0]: card=8 -> Hauppauge WinTV-HVR1700
[ 10.620921] cx23885[0]: card=9 -> Hauppauge WinTV-HVR1400
[ 10.620922] cx23885[0]: card=10 -> DViCO FusionHDTV7 Dual Express
[ 10.620923] cx23885[0]: card=11 -> DViCO FusionHDTV DVB-T Dual Express
[ 10.620924] cx23885[0]: card=12 -> Leadtek Winfast PxDVR3200 H
[ 10.620925] cx23885[0]: card=13 -> Compro VideoMate E650F
[ 10.620926] cx23885[0]: card=14 -> TurboSight TBS 6920
[ 10.620927] cx23885[0]: card=15 -> TeVii S470
[ 10.620928] cx23885[0]: card=16 -> DVBWorld DVB-S2 2005
[ 10.620929] cx23885[0]: card=17 -> NetUP Dual DVB-S2 CI
[ 10.620931] cx23885[0]: card=18 -> Hauppauge WinTV-HVR1270
[ 10.620932] cx23885[0]: card=19 -> Hauppauge WinTV-HVR1275
[ 10.620933] cx23885[0]: card=20 -> Hauppauge WinTV-HVR1255
[ 10.620934] cx23885[0]: card=21 -> Hauppauge WinTV-HVR1210
[ 10.620935] cx23885[0]: card=22 -> Mygica X8506 DMB-TH
[ 10.620936] cx23885[0]: card=23 -> Magic-Pro ProHDTV Extreme 2
[ 10.620937] cx23885[0]: card=24 -> Hauppauge WinTV-HVR1850
[ 10.620938] cx23885[0]: card=25 -> Compro VideoMate E800
[ 10.620939] cx23885[0]: card=26 -> Hauppauge WinTV-HVR1290
[ 10.620940] cx23885[0]: card=27 -> Mygica X8558 PRO DMB-TH
[ 10.620941] cx23885[0]: card=28 -> LEADTEK WinFast PxTV1200
[ 10.620942] cx23885[0]: card=29 -> GoTView X5 3D Hybrid
[ 10.620943] cx23885[0]: card=30 -> NetUP Dual DVB-T/C-CI RF
[ 10.620945] cx23885[0]: card=31 -> Leadtek Winfast PxDVR3200 H XC4000
[ 10.620946] cx23885[0]: card=32 -> MPX-885
[ 10.621091] CORE cx23885[0]: subsystem: 6981:8888, board: UNKNOWN/GENERIC [card=0,autodetected]
[ 10.749727] cx23885_dev_checkrevision() Hardware revision = 0xa5
[ 10.749732] cx23885[0]/0: found at 0000:03:00.0, rev: 4, irq: 16, latency: 0, mmio: 0xfb000000
[ 10.749739] cx23885 0000:03:00.0: setting latency timer to 64
Any ideas how to sort it? This method usually works first time every time.
I've tried...
rmmod cx23885
modprobe cx23885
No success.