I am trying to get a TBS 6920 running on YaVDR 0.5.0 (Ubunutu 12.04 with kernel 3.2.0-27-generic). I took the current driver package V130127 and installed it as described in the README file. Everything went fine, no errors were reported. After rebooting the machine the cx23885 module is not loaded automatically. After loding it manually (modprobe cx23885), there is still no /dev/dvb* device available. What can be the problem in my case? I really don't know, what do do now. Thanks in advance!
lspci:
- Code: Select All Code
03:00.0 Multimedia controller: Philips Semiconductors SAA7160 (rev 03)
Subsystem: Device 6922:0001
Physical Slot: 34
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [40] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [50] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [74] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Vendor Specific Information: Len=50 <?>
Capabilities: [100 v1] Vendor Specific Information: ID=0000 Rev=0 Len=088 <?>
dmesg part for the card at boot time:
- Code: Select All Code
[ 0.468236] pci 0000:03:00.0: [1131:7160] type 0 class 0x000480
[ 0.468285] pci 0000:03:00.0: reg 10: [mem 0xfea00000-0xfeafffff 64bit]
[ 0.468475] pci 0000:03:00.0: supports D1 D2
[ 0.468483] pci 0000:03:00.0: PME# supported from D0 D1 D2
[ 0.468496] pci 0000:03:00.0: PME# disabled
[ 0.468533] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
dmesg part when loading the module:
- Code: Select All Code
[ 80.490786] Linux media interface: v0.10
[ 80.497334] Linux video capture interface: v2.00
[ 80.520545] IR NEC protocol handler initialized
[ 80.521416] cx23885 driver version 0.0.3 loaded
[ 80.527016] IR RC5(x) protocol handler initialized
[ 80.531664] IR RC6 protocol handler initialized
[ 80.536586] IR JVC protocol handler initialized
[ 80.541228] IR Sony protocol handler initialized
[ 80.545991] IR MCE Keyboard/mouse protocol handler initialized
[ 80.550920] IR LIRC bridge handler initialized
Best regards,
Marco