I have successfully installed the TBS Linux drivers for my TBS6280 and it works correctly in tvheadend.
eg from dmesg
- Code: Select All Code
[ 22.566226] DVB: registering new adapter (SAA716x dvb adapter)
[ 23.196535] TurboSight TBS6280 DVB-T2 card MAC=ff:ff:ff:ff:ff:ff
[ 23.196538] DVB: registering adapter 0 frontend 0 (Sony CXD2820R (DVB-T/T2))...
[ 23.196787] DVB: registering new adapter (SAA716x dvb adapter)
[ 23.202683] TurboSight TBS6280 DVB-T2 card MAC=ff:ff:ff:ff:ff:ff
[ 23.202685] DVB: registering adapter 1 frontend 0 (Sony CXD2820R (DVB-T/T2))...
However I also have a Terratec 2400i dual tuner DVB-T pcie card that was working prior to installing the TBS drivers.
The page at http://www.linuxtv.org/wiki/index.php/T ... 400i_DVB-T says the card has been supported since kernel v3.9-rc1
I am running kernel: Linux xen 3.14-0.bpo.1-amd64 #1 SMP Debian 3.14.4-1~bpo70+1 (2014-05-14) x86_64 GNU/Linux
It seems support for this card is not included in the TBS drivers
eg the file ngene-cards.c in the kernel source has the following struct
- Code: Select All Code
static const struct pci_device_id ngene_id_tbl[] = {
NGENE_ID(0x18c3, 0xabc3, ngene_info_cineS2),
NGENE_ID(0x18c3, 0xabc4, ngene_info_cineS2),
NGENE_ID(0x18c3, 0xdb01, ngene_info_satixS2),
NGENE_ID(0x18c3, 0xdb02, ngene_info_satixS2v2),
NGENE_ID(0x18c3, 0xdd00, ngene_info_cineS2v5),
NGENE_ID(0x18c3, 0xdd10, ngene_info_duoFlex),
NGENE_ID(0x18c3, 0xdd20, ngene_info_duoFlex),
NGENE_ID(0x1461, 0x062e, ngene_info_m780),
NGENE_ID(0x153b, 0x1167, ngene_info_terratec),
{0}
};
while the corresponding struct in the TBS drivers is defined as follows
- Code: Select All Code
#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 8, 0)
static const struct pci_device_id ngene_id_tbl[] __devinitdata = {
#else
static const struct pci_device_id ngene_id_tbl[] = {
#endif
NGENE_ID(0x18c3, 0xabc3, ngene_info_cineS2),
NGENE_ID(0x18c3, 0xabc4, ngene_info_cineS2),
NGENE_ID(0x18c3, 0xdb01, ngene_info_satixS2),
NGENE_ID(0x18c3, 0xdb02, ngene_info_satixS2v2),
NGENE_ID(0x18c3, 0xdd00, ngene_info_cineS2v5),
NGENE_ID(0x18c3, 0xdd10, ngene_info_duoFlex),
NGENE_ID(0x18c3, 0xdd20, ngene_info_duoFlex),
NGENE_ID(0x1461, 0x062e, ngene_info_m780),
{0}
};
I believe it is the missing NGENE_ID(0x153b, 0x1167, ngene_info_terratec) line and supporting code that is causing my card to not be detected.
I can't seem to add an attachment to this post - so the relevant output of lspci is inline
- Code: Select All Code
01:00.0 Multimedia video controller [0400]: Micronas Semiconductor Holding AG nGene PCI-Express Multimedia Controller [18c3:0720]
Subsystem: TERRATEC Electronic GmbH Device [153b:1167]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at df9e0000 (32-bit, non-prefetchable) [size=64K]
Region 1: Memory at df9f0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Device Serial Number 00-00-00-07-20-3c-11-00
Capabilities: [400 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
- Code: Select All Code
05:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7160 [1131:7160] (rev 03)
Subsystem: Device [6280:0011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at dfd00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [40] MSI: Enable+ Count=1/32 Maskable- 64bit+
Address: 00000000fee00000 Data: 40a2
Capabilities: [50] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [74] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Vendor Specific Information: Len=50 <?>
Capabilities: [100 v1] Vendor Specific Information: ID=0000 Rev=0 Len=088 <?>
Kernel driver in use: SAA716x TBS
What is the best way to get both cards running at the same time?
Thanks
Mark